RealizedStudio Art Creation & Jewelry Design
  • Discover
    • About 關於瑞萊夢臻
    • Designs & Illustrations 設計圖稿插畫 >
      • Designs 2023
      • Designs 2022
      • Designs 2021
      • Designs 2020
      • Designs 2019
      • Designs 2018
      • Designs 2017
      • Designs 2016
      • Designs 2015
    • News 新消息
    • Contact 聯絡工作室
  • Gallery
    • Store Gallery
    • Pendants 墜飾
    • Rings 戒指
    • Earrings 耳飾
    • Cufflinks 袖扣
    • Brooch 別針
    • Bracelet 手飾
  • Shop
    • Online Shops 網路商店通路
    • Pinkoi
    • Creema
    • Etsy
    • ECPay 支付/ATM/CreditCard
    • Q&A 常見問答 >
      • Order and Shipping 訂購及配送
      • Ring Size Check 戒圍項鍊尺寸
      • Care Guide 產品保養建議
      • Return Policy 退換貨條例

[WIP] From Wax to Silver

9/25/2014

Comments

 
Picture
All models were packed individually.

These wax models were then sent to a local metalsmith workshop to cast into sterling silver. The result was quite nice. Some of the details not clearly seen in wax now appeared. All models came up clean without major failure. The next step of the process is to roughly polish the surface to remove the print marks on the models. Minor fixing is also required.

Here is a quick preview of some of the printed wax models from Shapeways and rough silver casted items:
Models from Shapeways were very carefully packed in individual boxes, but the foam in the box wasn't a very good choice in my opinion.

These w
ax models was a little softer than we usually use in jewelry practice. The material was a bit sticky too. The fabric from the foam was easily attached to the wax surface and hard to remove without leaving a scratch on the wax. Some models contains very thin and tiny parts (ex, prongs for stone setting) were even cut off by the foam fabric when removing the models from the box. I was not very please to see that those finally printed models in success, failed in the last step due to packaging.
Picture
Prongs were cut off from the model when unpacking...

Read More
Comments

Wax models on their way here!

9/8/2014

Comments

 
There is a phone call today informing that those wax models of the new jewelry designs are on their way to the studio!
All wax models are produced by the world-leading 3D printing company, Shapeways. With this RP technology becoming more friendly and easy accessible to end users, the dreams at the studio are moving forward as well!

Check out our store at the Shapeways, you may  also try out our designs with their quality jewelry printing productions!

Comments

    瑞萊夢臻工作室

    RealizedStudio


    Categories

    All
    3D Model
    Contest
    Designs
    WIP


    Archives

    September 2019
    December 2018
    July 2018
    March 2018
    February 2018
    December 2017
    November 2017
    September 2017
    April 2017
    December 2016
    November 2016
    October 2016
    September 2016
    February 2016
    November 2015
    July 2015
    March 2015
    December 2014
    September 2014


    RSS Feed

About

  • 關於 About
  • 圖稿 Designs
  • 新消息 News
  • 聯絡我們 Contact

Gallery

  • 墜飾 Pendants
  • 戒指 Rings
  • 耳飾 Earrings
  • 袖扣 Cufflinks
  • 別針 Brooches
  • 手飾 Bracelets

Service Q&A

  • 訂購配送 Order & Shipping
  • 戒圍尺寸 Ring Size
  • 保養建議 Care Guide
  • 退換貨條例 Return Policy

Copyright ©  2022 - RealizedStudio by Eugene YJ Chen. All Rights Reserved.

  • Discover
    • About 關於瑞萊夢臻
    • Designs & Illustrations 設計圖稿插畫 >
      • Designs 2023
      • Designs 2022
      • Designs 2021
      • Designs 2020
      • Designs 2019
      • Designs 2018
      • Designs 2017
      • Designs 2016
      • Designs 2015
    • News 新消息
    • Contact 聯絡工作室
  • Gallery
    • Store Gallery
    • Pendants 墜飾
    • Rings 戒指
    • Earrings 耳飾
    • Cufflinks 袖扣
    • Brooch 別針
    • Bracelet 手飾
  • Shop
    • Online Shops 網路商店通路
    • Pinkoi
    • Creema
    • Etsy
    • ECPay 支付/ATM/CreditCard
    • Q&A 常見問答 >
      • Order and Shipping 訂購及配送
      • Ring Size Check 戒圍項鍊尺寸
      • Care Guide 產品保養建議
      • Return Policy 退換貨條例